Toshiba e-Studio 457 Коды ошибок

  • Code: C010
  • Description: Main motor abnormality: The main motor is not rotating normally
  • Code: C040
  • Description: PFP motor abnormality: The PFP motor is not rotating normally
  • Code: C130
  • Description: Upper drawer tray abnormality: The upper drawer tray motor is not rotating or the upper drawer tray is not moving normally.
  • Code: C140
  • Description: Lower drawer tray abnormality: The lower drawer tray motor is not rotating or the lower drawer tray is not moving normally
  • Code: C150
  • Description: PFP upper drawer tray abnormality: The PFP upper drawer tray motor is not rotating or the PFP upper drawer tray is not moving normally
  • Code: C160
  • Description: PFP lower drawer tray abnormality: The PFP lower drawer tray motor is not rotating or the PFP lower drawer tray is not moving normal
  • Code: C180
  • Description: LCF tray-up motor abnormality: The LCF tray-up motor is not rotating or the LCF tray is not moving normally.
  • Code: C1A0
  • Description: LCF end fence motor abnormality: The LCF end fence motor is not rotating or the LCF end fence is not moving normally.
  • Code: C1B0
  • Description: LCF transport motor abnormality: The LCF transport motor is not rotating normally.
  • Code: C260
  • Description: Peak detection error: Lighting of the exposure lamp (white reference) is not detected when power is turned ON.
  • Code: C270
  • Description: Carriage home position sensor not turning OFF within a specified period of time: The carriage does not shift from its home position in a specified period of time.
  • Code: C280
  • Description: Carriage home position sensor not turning ON within a specified period of time: The carriage does not reach to its home position in a specified period of time.
  • Code: C290
  • Description: Scanner fuse blowout: 24V power for the scanning system is not supplied at the scanner warming-up after power-ON.
  • Code: C3D0
  • Description: EPU board memory overwriting error: The overwriting of the EPU board memory fails.
  • Code: C3D1
  • Description: EPU board memory new parts detection error: The EPU board detects the process unit as a new unit when the equipment is started in the normal mode.
  • Code: C3D2
  • Description: EPU board memory old parts detection error: The EPU board cannot detect the new process unit when the equipment is started in the EPU replacement mode ([7] + [START]).
  • Code: C410
  • Description: Thermistor or heater abnormality at power-ON: Abnormality of service call the thermistor is detected when power is turned ON or the temperature of the fuser roller does not rise in a specified period of time after power is turned ON.
  • Code: C430
  • Description: Thermistor abnormality after abnormality judgment: Abnormality of the thermistor is detected after a specified period of time has passed from power-ON (including ready state).
  • Code: C440
  • Description: Heater abnormality after abnormality judgment: The temperature of the fuser roller has exceeded the range of control or does not even reach the range.
  • Code: C450
  • Description: Thermistor abnormality during printing: Abnormality of the thermistor is detected during printing.
  • Code: C4C0
  • Description: Fuser unit new/old detection fuse abnormality
  • Code: C550
  • Description: RADF I/F error: Communication error has occurred between the RADF and the scanner.
  • Code: C551
  • Description: Document feeder model detection error: An optional document feeder that is not compatible to this equipment is installed.
  • Code: C570
  • Description: Communication error between Engine-CPU and IPC board
  • Code: C580
  • Description: Communication error between IPC board and finisher
  • Code: C5A0
  • Description: EEPROM communication abnormality (LGC board)
  • Code: C8E0
  • Description: ADF communication abnormality: The system has to be stopped because the control abnormality occurred
  • Code: C940
  • Description: Engine-CPU abnormality
  • Code: C970
  • Description: High-voltage transformer abnormality: Leakage of the main charger is detected.
  • Code: CA10
  • Description: Polygonal motor abnormality: The polygonal motor is not rotating normally.
  • Code: CA20
  • Description: H-Sync detection error: H-Sync detection PC board cannot detect laser beams.
  • Code: CB00
  • Description: Finisher not connected
  • Code: CB01
  • Description: Finisher communication error
  • Code: CB10
  • Description: Entrance motor abnormality: The entrance motor is not rotating normally. [MJ-1101/MJ-1106]
  • Code: CB11
  • Description: Buffer tray guide motor abnormality: The buffer tray guide motor is not rotating or the buffer tray guide is not moving normally. [MJ-1101/MJ-1106]
  • Code: CB12
  • Description: Buffer roller drive motor abnormality: The buffer roller drive motor is not rotating or the buffer roller is not moving normally. [MJ-1101/MJ-1106]
  • Code: CB13
  • Description: Finisher exit motor abnormality [MJ-1101/MJ-1106]
  • Code: CB14
  • Description: Paper holding arm motor abnormality [MJ-1101/MJ-1106]
  • Code: CB30
  • Description: Movable tray shift motor abnormality: The movable tray shift motor is not rotating or the movable tray is not moving normally. [MJ-1101] Movable tray shift motor abnormality: The movable tray shift motor or the movable tray does not work properly. [MJ-1032] Movable tray shift motor abnormality: The movable tray shift motor or the movable tray does not work properly. [MJ-1033]
  • Code: CB31
  • Description: Movable tray paper-full detection error: The actuator of the movable tray paper-full detection sensor does not move smoothly. [MJ-1101/MJ-1106]
  • Code: CB40
  • Description: Front alignment motor abnormality: The front alignment motor is not rotating or the front align/1106ment plate is not moving normally. [MJ-1101] Front alignment plate home position detection error: The detection of the home position ends abnormally because the front alignment plate has not worked properly. [MJ-1032/MJ-1033]
  • Code: CB50
  • Description: Stapler home position error: The stapler home position sensor does not work. [MJ-1101/MJ-1106] Stapler unit home position detection error: The detection of the home position of the stapler unit ends abnormally. [MJ-1032/MJ-1033
  • Code: CB51
  • Description: Stapler shift home position error: The stapler is not at the home position. [MJ-1101/MJ-1106] Stapler unit sliding home position detection error: The detection of the home position of the stapler unit sliding ends abnormally. [MJ-1032/MJ-1033]
  • Code: CB60
  • Description: Stapler shift motor abnormality: Stapler shift motor is not rotating or staple unit is not moving normally. [MJ-1101/MJ-1106]
  • Code: CB80
  • Description: Backup RAM data abnormality: Abnormality of checksum value on finisher controller PC board is detected when the power is turned ON. [MJ-1101/MJ-1106] EEPROM data abnormality: An error occurs during the writing of data into the EEPROM of the Finisher. [MJ- 1032/MJ-1033]
  • Code: CB81
  • Description: Flash ROM abnormality: Abnormality of checksum value on finisher controller PC board is detected when the power is turned ON. [MJ-1101/MJ-1106]
  • Code: CB82
  • Description: Finisher - Main CPU program error
  • Code: CB83
  • Description: Saddle Stitch Finisher - Main CPU program error [MJ- 1106]
  • Code: CB84
  • Description: Hole Punch Unit - Main CPU program error
  • Code: CB90
  • Description: Paper pushing plate motor abnormality: Paper pushing plate motor is not rotating or paper pushing plate is not moving normally.
  • Code: CB91
  • Description: Saddle Stitch Finisher flash ROM abnormality [MJ-1106]
  • Code: CB92
  • Description: Saddle Stitch Finisher RAM abnormality [MJ-1106]
  • Code: CB93
  • Description: Additional folding motor abnormality [MJ-1106]
  • Code: CB94
  • Description: Saddle transport motor abnormality [MJ-1106]
  • Code: CB95
  • Description: Stacker motor abnormality [MJ-1106]
  • Code: CBA0
  • Description: Front saddle stapler home position error: The stapler home position detection is abnormally operated and finished. [MJ-1106]
  • Code: CBB0
  • Description: Rear saddle stapler home position error: The stapler home position detection is abnormally operated and finished. [MJ-1106]
  • Code: CBC0
  • Description: Saddle Stitch Finisher side alignment motor (M15) abnormality: The alignment motor is not rotating or the alignment plate is not working properly. [MJ- 1106]
  • Code: CBE0
  • Description: Saddle Stitch Finisher folding motor (M17) abnormality: The folding motor is not rotating or the folding roller is not moving normally. [MJ-1106]
  • Code: CBF0
  • Description: Stacker motor (M9) abnormality : The stacker motor is not rotating. [MJ-1033]
  • Code: CC01
  • Description: A model not supporting the Finisher is connected. Note that this error is recognized in the communication converter and is output.
  • Code: CC02
  • Description: Stack exit roller nip home position detection error: The detection of the home position of the stack exit roller nip ends abnormally. [MJ-1032/MJ-1033]
  • Code: CC20
  • Description: Saddle communication error [MJ-1106]
  • Code: CC21
  • Description: The detection of the home position of the saddle stitch 3rd transport roller drive motor ends abnormally.
  • Code: CC22
  • Description: The detection of the home position of the saddle stitch stapler unit ends abnormally.
  • Code: CC30
  • Description: Stack transport motor abnormality: The stack transport motor is not rotating or the stack transport belt is not moving normally. [MJ-1101/MJ-1106]
  • Code: CC31
  • Description: Transport motor abnormality: The transport motor is not rotating or the stack transport roller -1 and -2 is not rotating normally. [MJ-1101/MJ-1106]
  • Code: CC41
  • Description: Paper holder cam home position abnormality: The paper holder cam is not at the home position. [MJ- 1101]
  • Code: CC51
  • Description: Sideways adjustment motor (M2) abnormality: Sideways adjustment motor is not rotating or puncher is not shifting normally. [MJ-1101/MJ-1106 (when MJ-6103 is installed)]
  • Code: CC52
  • Description: Skew adjustment motor (M1) abnormality: Skew adjustment motor is not rotating or puncher is not shifting normally. [MJ-1101/MJ-1106 (when MJ- 6103 is installed)]
  • Code: CC53
  • Description: An abnormality occurs in the punch waste full sensor.
  • Code: CC54
  • Description: Hole punch registration sensor detection error: An abnormality occurs in the hole punch registration sensor. [MJ-1032/MJ-1033]
  • Code: CC60
  • Description: Punch motor abnormality: Punch motor is not rotating or puncher is not shifting normally.]
  • Code: CC61
  • Description: Punch motor (M3) home position detection error: Punch motor is not rotating or puncher is not shifting normally. [MJ-1101/MJ-1106 (when MJ-6103 is installed)]
  • Code: CC71
  • Description: Punch ROM checksum error: Abnormality of checksum value on Hole punch controller PC board is detected when the power is turned on. [MJ-1101/MJ-1106 (when MJ-6103 is installed)]
  • Code: CC72
  • Description: Punch RAM read/write error: Abnormality of checksum value on Hole punch controller PC board is detected when the power is turned on. [MJ-1101/MJ-1106 (when MJ-6103 is installed)]
  • Code: CC80
  • Description: Rear alignment motor abnormality: The rear alignment motor is not rotating or the rear alignment plate is not moving normally. [MJ-1101/MJ-1106] Rear alignment plate home position detection error: The detection of the home position ends abnormally because the rear alignment plate has not worked properly. [MJ-1032/MJ-1033]
  • Code: CC91
  • Description: The detection of the home position of the gripper arm ends abnormality.
  • Code: CC92
  • Description: The movable tray exceeds its upper limit.
  • Code: CC93
  • Description: Knurled roller shift solenoid abnormality: An abnormality occurs in the knurled roller shift solenoid. [MJ-1032]
  • Code: CC94
  • Description: 1st fan motor abnormality: The 1st fan motor is locked abnormally. [MJ-1032]
  • Code: CCF1
  • Description: Tray safety switch abnormality - The tray safety switch turned on during tray operation (moving up or down).
  • Code: CDE0
  • Description: Paddle motor abnormality: The paddle motor does not rotate properly.
  • Code: CDF0
  • Description: Initialization error of the offset tray: The home position of the separator cannot be detected when the power is turned ON.
  • Code: CE00
  • Description: Communication error between finisher unit and puncher unit: Communication error between the finisher controller PC board and punch controller PC board.
  • Code: CE50
  • Description: Temperature/humidity sensor abnormality: The output value of this sensor is out of a specified range.
  • Code: CE90
  • Description: Drum thermistor abnormality: The output value of the drum thermistor-K is out of a specified range.
  • Code: CF10
  • Description: Communication module SRAM reading failure. [MJ-1101]
  • Code: E010
  • Description: Jam not reaching the exit sensor: The paper which has passed through the fuser unit does not reach the exit sensor.
  • Code: E020
  • Description: Stop jam at the exit sensor: The trailing edge of the paper does not pass the exit sensor after its leading edge has reached this sensor.
  • Code: E030
  • Description: Power-ON jam: The paper is remaining on the paper transport path when power is turned ON.
  • Code: E061
  • Description: Incorrect paper size setting for upper drawer: The size of paper in the 1st drawer differs from size setting of the equipment.
  • Code: E062
  • Description: Incorrect paper size setting for lower drawer: The size of paper in the 2nd drawer differs from size setting of the equipment.
  • Code: E063
  • Description: Incorrect paper size setting for PFP upper drawer: The size of paper in the 3rd drawer differs from size setting of the equipment.
  • Code: E064
  • Description: Incorrect paper size setting for PFP lower drawer: The size of paper in the 4th drawer differs from size setting of the equipment.
  • Code: E065
  • Description: Incorrect paper size setting for bypass tray: The size of paper in the bypass tray differs from size setting of the equipment
  • Code: E090
  • Description: HDD abnormality causes jam: Image data to be printed cannot be prepared.
  • Code: E110
  • Description: ADU misfeeding (Paper not reaching the registration sensor): The paper which has passed through ADU does not reach the registration sensor during duplex printing
  • Code: E120
  • Description: Bypass misfeeding (Paper not reaching the 1st transport sensor): The paper fed from the bypass tray does not reach the 1st transport sensor
  • Code: E130
  • Description: Upper drawer misfeeding (Paper not reaching the 1st transport sensor): The paper fed from the upper drawer does not reach the 1st transport sensor.
  • Code: E140
  • Description: Lower drawer misfeeding (Paper not reaching the 2nd transport sensor): The paper fed from the lower drawer does not reach the 2nd transport sensor.
  • Code: E150
  • Description: PFP upper drawer misfeeding (Paper not reaching the PFP upper drawer feed sensor): The paper fed from the PFP upper drawer does not reach the PFP upper drawer feed sensor.
  • Code: E160
  • Description: PFP lower drawer misfeeding (Paper not reaching the PFP lower drawer feed sensor): The paper fed from the PFP lower drawer does not reach the PFP lower drawer feed senso
  • Code: E190
  • Description: LCF misfeeding (Paper not reaching the LCF feed sensor): The paper fed from the LCF does not reach the LCF feed sensor.
  • Code: E200
  • Description: Upper drawer transport jam (Paper not reaching the registration sensor): The paper does not reach the registration sensor after it has passed the 1st transport sensor.
  • Code: E210
  • Description: Lower drawer transport jam (Paper not reaching the registration sensor): The paper does not reach the registration sensor after it has passed the 1st transport sensor
  • Code: E220
  • Description: Lower drawer transport jam (Paper not reaching the 1st transport sensor): The paper does not reach the 1st transport sensor after it has passed the lower drawer feed sensor.
  • Code: E270
  • Description: Bypass transport jam (paper not reaching the registration sensor): The paper does not reach the registration sensor after it has passed the 1st transport sensor.
  • Code: E280
  • Description: ADU transport jam (paper not reaching the registration sensor): The paper which has passed through ADU and the 1st transport sensor does not reach the registration sensor during duplex printing
  • Code: E300
  • Description: PFP upper drawer transport jam (Paper not reaching the registration sensor): The paper does not reach the registration sensor after it has passed the 1st transport sensor.
  • Code: E310
  • Description: PFP upper drawer transport jam (Paper not reaching the 1st transport sensor): The paper does not reach the 1st transport sensor after it has passed the 2nd transport sensor.
  • Code: E320
  • Description: PFP upper drawer transport jam (Paper not reaching the 2nd transport sensor): The paper does not reach the 2nd transport sensor after it has passed the PFP upper drawer feed sensor.
  • Code: E330
  • Description: PFP lower drawer transport jam (Paper not reaching the registration sensor): The paper does not reach the registration sensor after it has passed the 1st transport sensor.
  • Code: E340
  • Description: PFP lower drawer transport jam (Paper not reaching the 1st transport sensor): The paper does not reach the 1st transport sensor after it has passed the PFP lower drawer feed sensor.
  • Code: E350
  • Description: PFP lower drawer transport jam (Paper not reaching the 2nd transport sensor): The paper does not reach the 2nd transport sensor after it has passed the PFP upper drawer feed sensor.
  • Code: E360
  • Description: PFP lower drawer transport jam (Paper not reaching the PFP upper drawer feed sensor): The paper does not reach the PFP upper drawer feed sensor after it has passed the PFP lower drawer feed sensor.
  • Code: E3C0
  • Description: LCF transport jam (Paper not reaching the registration sensor): The paper does not reach the registration sensor after it has passed the 1st transport sensor.
  • Code: E3D0
  • Description: LCF transport jam (Paper not reaching the 1st transport sensor): The paper does not reach the 1st transport sensor after it has passed the 2nd transport sensor.
  • Code: E3E0
  • Description: LCF transport jam (Paper not reaching the 2nd transport sensor): The paper does not reach the 2nd transport sensor after it has passed the LCF feed sensor.
  • Code: E410
  • Description: Front cover open jam: The front cover has opened during printing.
  • Code: E420
  • Description: PFP side cover open jam: The PFP side cover has opened during printing.
  • Code: E430
  • Description: ADU open jam: The ADU has opened during printing
  • Code: E440
  • Description: Feed cover open jam: The feed cover has opened during printing.
  • Code: E450
  • Description: LCF side cover open jam: The LCF side cover has opened during printing.
  • Code: E480
  • Description: Bridge unit open jam: The bridge unit has opened during printing.
  • Code: E490
  • Description: Job separator cover open jam: The job separator cover has opened during printing.
  • Code: E491
  • Description: Offset tray cover open jam: The offset tray cover has opened during printing.
  • Code: E510
  • Description: Jam not reaching the ADU entrance sensor: The paper does not reach the ADU entrance sensor after it is switchbacked in the exit section.
  • Code: E520
  • Description: Stop jam in the ADU: The paper does not reach the ADU exit sensor after it has passed the ADU entrance sensor.
  • Code: E550
  • Description: Paper remaining jam on the transport path: The paper is remaining on the transport path when printing is finished (caused by a multiple paper feeding).
  • Code: E570
  • Description: Jam not reaching the reverse sensor: The paper which has passed the exit sensor does not reach the reverse sensor
  • Code: E580
  • Description: Stop jam at the reverse sensor: The trailing edge of the paper does not pass the reverse sensor after its leading edge has reached this sensor
  • Code: E712
  • Description: Jam not reaching the registration sensor: The original fed from the original feeding tray does not reach the registration sensor.
  • Code: E714
  • Description: Feed signal reception jam: The feed signal is received even no original exists on the original feeding tray.
  • Code: E721
  • Description: Jam not reaching the read sensor: The original does not reach the read sensor after it has passed the registration sensor (when scanning obverse side) or the reverse sensor (when scanning reverse side).
  • Code: E722
  • Description: Jam not reaching the exit sensor (during scanning): The original which passed the read sensor does not reach the exit sensor when it is transported from the scanning section to exit section.
  • Code: E724
  • Description: Stop jam at the registration sensor: The trailing edge of the original does not pass the registration sensor after its leading edge has reached this sensor.
  • Code: E725
  • Description: Stop jam at the read sensor: The trailing edge of the original does not pass the read sensor after its leading edge has reached this sensor.
  • Code: E731
  • Description: Stop jam at the exit sensor: The trailing edge of the original does not pass the exit sensor after its leading edge has reached this sensor.
  • Code: E860
  • Description: RADF jam access cover open: The RADF jam access cover has opened during RADF operation.
  • Code: E870
  • Description: RADF open jam: RADF has opened during RADF operation.
  • Code: E871
  • Description: Cover open jam in the read ready status: Jam caused by opening of the RADF jam access cover or front cover while the RADF is waiting for the scanning start signal from the equipment.
  • Code: E910
  • Description: Jam at the bridge unit transport sensor-1: The paper does not reach the bridge unit transport sensor-1 after it has passed the exit sensor.
  • Code: E920
  • Description: Stop jam at the bridge unit transport sensor-1: The trailing edge of the paper does not pass the bridge unit transport sensor-1 after its leading edge has reached the sensor.
  • Code: E930
  • Description: Jam at the bridge unit transport sensor-2: The trailing edge of the paper does not reach the bridge unit transport sensor-2 after its leading edge has reached the bridge unit transport sensor-1.
  • Code: E940
  • Description: Stop jam at the bridge unit transport sensor-2: The trailing edge of the paper does not reach the bridge unit transport sensor-2 after its leading edge has reached the bridge unit transport sensor-2.
  • Code: E950
  • Description: Jam not reaching the job separator transport sensor: The paper has passed through the exit sensor does not reach the job separator transport sensor.
  • Code: E951
  • Description: Stop jam at the job separator transport sensor: The trailing edge of the paper does not pass the job separator transport sensor
  • Code: E960
  • Description: Jam not reaching the offset tray transport sensor: The paper has passed through the exit sensor does not reach the offset tray transport sensor.
  • Code: E961
  • Description: Stop jam at the offset tray transport sensor: The trailing edge of the paper does not pass the offset tray transport sensor.
  • Code: E9F0
  • Description: Punching jam: Punching is not performed properly. [MJ-1025 (When MJ-6005 is installed)] Punching jam: Punching is not performed properly. [MJ-1024 (when MJ-6004 is installed)] [MJ-1101 (when MJ-6101 is installed)]
  • Code: EA10
  • Description: Paper transport delay jam: The paper which has passed the bridge unit does not reach the inlet sensor. Paper transport delay jam: The paper which has passed the bridge unit does not reach the inlet sensor. [MJ-1024/1031/1101]
  • Code: EA20
  • Description: Paper transport stop jam: The paper does not pass through the inlet sensor. [MJ-1025/MJ-1031] Paper transport stop jam: The paper has passed through the inlet sensor but does not reach or pass the feed path sensor or processing tray sensor. [MJ-1024] Paper transport delay jam: The paper which has passed through the inlet sensor does not reach the transport sensor. [MJ- 1101
  • Code: EA21
  • Description: Paper size error jam: Paper does not reach the sensor because the paper is shorter than spec.
  • Code: EA22
  • Description: Paper transport jam (Finisher paper punching edge detection sensor)
  • Code: EA23
  • Description: Paper transport jam (exit sensor)
  • Code: EA24
  • Description: Paper transport jam (between entrance and exit sensors)
  • Code: EA25
  • Description: Paper transport jam (after paper stack exit)
  • Code: EA26
  • Description: Paper transport jam (stop command request)
  • Code: EA27
  • Description: Paper transport jam (paper not inserted)
  • Code: EA28
  • Description: Paper transport jam (assisting arm operation delay)
  • Code: EA29
  • Description: Paper transport jam (stack transport delay)
  • Code: EA30
  • Description: Power-ON jam: Paper exists at the inlet sensor when power is turned ON.
  • Code: EA31
  • Description: Transport path paper remaining jam
  • Code: EA32
  • Description: Exit paper remaining jam
  • Code: EA40
  • Description: Door open jam: The Finisher is released from the equipment or any of the staple door and top cover is opened during printing. [MJ-1025] Door open jam: Any of the upper cover and front cover of the Finisher or any of the upper door and front door of the Hole Punch Unit is opened during printing. [MJ-1024] Joint open jam: The joint is released during printing or in the standby status. [MJ-1031]
  • Code: EA50
  • Description: Stapling jam: Stapling is not performed properly.
  • Code: EA60
  • Description: Early arrival jam: The inlet sensor detects the paper earlier than a specified timing
  • Code: EA70
  • Description: Stack delivery jam: It cannot deliver the stack of paper on the intermediary process tray to the stack tray. [MJ-1025] Stack slider home position error: The stack slider is not at the home position. [MJ-1031]
  • Code: EA80
  • Description: Stapling jam: Stapling is not performed properly. [MJ-1024]
  • Code: EA90
  • Description: Door open jam: The delivery cover or inlet cover has opened during printing [MJ-1024/MJ-1101].
  • Code: EAA0
  • Description: Power-ON jam: Paper exists at No.1 paper sensor, No. 2 paper sensor, No.3 paper sensor, vertical path paper sensor or delivery sensor when power is turned ON. [MJ-1024/MJ-1101]
  • Code: EAB0
  • Description: Saddle paper transport stop jam: The paper which passed through the inlet sensor does not reach or pass through the folding position sensor. [MJ-1025]
  • Code: EAC0
  • Description: Saddle transport delay jam: The paper which has reached the inlet sensor does not pass through this sensor. [MJ-1025/MJ-1024]
  • Code: EAD0
  • Description: Print end command time-out jam: The printing has not finished normally because of the communication error between the SYS board and LGC board at the end of printing.
  • Code: EAE0
  • Description: Receiving time time-out jam: The printing has been interrupted because of the communication error between the equipment and finisher when the paper is transported from the equipment to the finisher.
  • Code: EB30
  • Description: Ready time time-out jam: The equipment judges that the paper transport to the finisher is disabled because of the communication error between the equipment and finisher at the start of printing.
  • Code: EB50
  • Description: Paper remaining on the transport path: The multiple feeding of preceding paper caused the misfeeding of upcoming paper.
  • Code: EB60
  • Description: Paper remaining on the transport path: The multiple feeding of preceding paper caused the misfeeding of upcoming paper (redetection after no jam is detected at [EB50]).
  • Code: ED10
  • Description: Skew adjustment motor home position detection abnormality: The Skew adjustment motor is not at the home position. [MJ-1101 (when MJ-6101 is installed)]
  • Code: ED11
  • Description: Sideways adjustment motor home position detection error: The Sideways adjustment motor is not at the home position. [MJ-1101 (when MJ-6101 is installed)]
  • Code: ED12
  • Description: Shutter home position error: The shutter is not at the home position. [MJ-1101]
  • Code: ED13
  • Description: Front alignment plate home position error: The front alignment plate is not at the home position. [MJ- 1101]
  • Code: ED14
  • Description: Rear alignment plate home position error: The rear alignment plate is not at the home position. [MJ- 1101]
  • Code: ED15
  • Description: Paddle home position error: The paddle is not at the home position. [MJ-1101]
  • Code: ED16
  • Description: Buffer tray home position error: The buffer tray is not at the home position. [MJ-1101]
  • Code: F070
  • Description: Communication error between System-CPU and Engine- CPU
  • Code: F090
  • Description: SRAM abnormality on the SYS board
  • Code: F100_0
  • Description: HDD format error: Operation of HDD key data fails.
  • Code: F100_1
  • Description: HDD format error: Encryption key data of either the SYS board or the SRAM board for the SYS board are damaged.
  • Code: F100_2
  • Description: HDD format error: Encryption key data of both the SYS board and the SRAM board for the SYS board are damaged.
  • Code: F101
  • Description: The HDD cannot be connected (mounted) caused by a reason other than one described in the F101_0 through F101_3 errors.
  • Code: F101_0
  • Description: HDD connection error (HDD connection cannot be detected.)
  • Code: F101_1
  • Description: Root partition mount error (HDD formatting fails.): The HDD cannot be connected (mounted) caused by damage to the areas in which the program is mainly stored.
  • Code: F101_2
  • Description: Normal partition mount error (HDD normal partition mounting fails.): The HDD cannot be connected (mounted) caused by damage to areas other than those described in the F101_0 and F101_1 errors.
  • Code: F101_3
  • Description: Encryption partition mount error (HDD encryption partition mounting fails.): The HDD cannot be connected (mounted) caused by damage to the areas in which the key is stored.
  • Code: F102
  • Description: HDD start error: HDD cannot become ‘Ready’ state.
  • Code: F103
  • Description: HDD transfer time-out: Reading/writing cannot be performed in the specified period of time.
  • Code: F104
  • Description: HDD data error: Abnormality is detected in the data of HDD.
  • Code: F105
  • Description: HDD other error
  • Code: F106_0
  • Description: ADI-HDD error: Illegal disk replacement detected (ADIHDD Exchange to SATA-HDD)
  • Code: F106_1
  • Description: ADI-HDD error: HDD type detection error
  • Code: F106_2
  • Description: ADI-HDD error: ADI encryption key download operation error
  • Code: F106_3
  • Description: ADI-HDD error: ADI authentication Admin Password generation error
  • Code: F106_4
  • Description: ADI-HDD error: Authentication random number generation error
  • Code: F106_5
  • Description: ADI-HDD error: Authentication data transmission error
  • Code: F109_0
  • Description: Key consistency error: Consistency check operation error.
  • Code: F109_1
  • Description: Key consistency error: SRAM encryption AES key data damage.
  • Code: F109_2
  • Description: Key consistency error: Signature Check public key damage.
  • Code: F109_3
  • Description: Key consistency error: HDD encryption parameter damage.
  • Code: F109_4
  • Description: Key consistency error: license data damage.
  • Code: F109_5
  • Description: Key consistency error: Encryption key for ADI-HDD is damaged
  • Code: F109_6
  • Description: Key consistency error: Administrator password error for ADI-HDD authentication.
  • Code: F110
  • Description: Communication error between System-CPU and Scanner-CPU
  • Code: F111
  • Description: Scanner response abnormality
  • Code: F120
  • Description: Database abnormality: Database is not operating normally.
  • Code: F121
  • Description: Database abnormality (user information management database)
  • Code: F122
  • Description: Database abnormality (Message/Job log management database)
  • Code: F124
  • Description: Database abnormality : Database is not operating normally. (Language management database)
  • Code: F130
  • Description: Invaid MAC address
  • Code: F131
  • Description: Error due to damage to filtering setting file
  • Code: F140
  • Description: ASIC format error: ASIC formatting fails or memory acquiring fails when software is formatted.
  • Code: F200
  • Description: Data Overwrite option (GP-1070) disabled
  • Code: F350
  • Description: SLG board abnormality
  • Code: F400
  • Description: SYS board cooling fan abnormality
  • Code: F500
  • Description: HD partition damage
  • Code: F510
  • Description: Application start error
  • Code: F520
  • Description: Operating system start error
  • Code: F521
  • Description: Integrity check error
  • Code: F550
  • Description: Encryption partition error
  • Code: F600
  • Description: Software update error
  • Code: F700
  • Description: Overwrite error
  • Code: F800
  • Description: Date error
  • Code: F900
  • Description: Model information error
  • Code: F901
  • Description: Engine speed error: The speed information of the LGC board is damaged.
  • Code: F901_1
  • Description: Engine speed error: The speed information of the LGC board is damaged.

МФУ SHARP
МФУ TOSHIBA
BCP TOSHIBA
Совместимые картриджи G&G

Поиск по каталогу:

Наименование


Empty cart
Корзина пуста

 МЫ ПРЕДЛАГАЕМ СПЕЦИАЛЬНЫЕ УСЛОВИЯ СОТРУДНИЧЕСТВА ДЛЯ КОРПОРАТИВНЫХ КЛИЕНТОВ И СЕРВИСНЫХ ЦЕНТРОВ