Toshiba e-Studio 281c Коды ошибок

  • Code: C010
  • Description: Main motor abnormality: The main motor is not rotating normally.
  • Code: C020
  • Description: Developer drive motor abnormality: The developer drive motor is not rotating normally.
  • Code: C030
  • Description: Transport motor abnormality: The transport motor is not rotating normally.
  • Code: C040
  • Description: PFP motor abnormality: The PFP motor is not rotating normally. (the case that paper can be fed from any drawer except the PFP)
  • Code: C130
  • Description: 1st drawer tray abnormality: The tray-up motor is not rotating or the 1st drawer tray is not moving normally. (the case that paper can be fed from any drawer except the 1st drawer)
  • Code: C140
  • Description: 2nd drawer tray abnormality: The tray-up motor is not rotating or the 2nd drawer tray is not moving normally. (the case that paper can be fed from any drawer except the 2nd drawer)
  • Code: C150
  • Description: PFP upper drawer tray abnormality: The PFP upper drawer tray-up motor is not rotating or the PFP upper drawer tray is not moving normally. (the case that paper can be fed from any drawer except the PFP upper drawer)
  • Code: C160
  • Description: PFP lower drawer tray abnormality: The PFP lower drawer tray-up motor is not rotating or the PFP lower drawer tray is not moving normally. (the case that paper can be fed from any drawer except the PFP lower drawer)
  • Code: C180
  • Description: LCF tray-up motor abnormality: The LCF trayup motor is not rotating or the LCF tray is not moving normally. (the case that paper can be fed from any drawer except the LCF)
  • Code: C1A0
  • Description: LCF end fence motor abnormality: The LCF end fence motor is not rotating or the LCF end fence is not moving normally. (the case that paper can be fed from any drawer except the LCF)
  • Code: C1B0
  • Description: LCF transport motor abnormality: The LCF transport motor is not rotating normally (when paper can be fed from any drawer except the LCF).
  • Code: C260
  • Description: Peak detection error: Lighting of the exposure lamp (white reference) is not detected when power is turned ON.
  • Code: C270
  • Description: (1) Carriage home position sensor not turning OFF within a specified period of time: The carriage does not shift from its home position in a specified time.
    (2) Downloading firmware with an incorrect model. If the error occurs, the exposure lamp lights twice at the same time.
  • Code: C280
  • Description: Carriage home position sensor not going ON within a specified time
  • Code: C360
  • Description: Charger cleaner motor abnormality: Charger cleaner motor is not rotating or wire cleaner is not moving normally
  • Code: C411
  • Description: Thermistor or heater lamp abnormality at power-ON: Abnormality of the thermistor is detected when power is turned ON or the temperature of the fuser roller does not rise in a specified period of time after power is turned ON.
  • Code: C412
  • Description: Thermistor/heater lamp abnormality at power- ON: Thermistor abnormality is detected at power-ON or the fuser roller temperature does not rise within a specified period of time after power-ON.
  • Code: C443
  • Description: Heater lamp abnormality after abnormality judgment (not reaching to intermediate temperature)
  • Code: C445
  • Description: Heater lamp abnormality after abnormality judgment (pre-running end temperature abnormality)
  • Code: C446
  • Description: Heater lamp abnormality after abnormality judgment (pre-running end temperature abnormality)
  • Code: C447
  • Description: Heater lamp abnormality after abnormality judgment (temperature abnormality at ready status)
  • Code: C448
  • Description: Heater lamp continuous lighting abnormality: Heater lamp lights continuously for a certain period of time when the pressure roller temperature during ready status is higher than the specified
  • Code: C471
  • Description: IH power voltage abnormality or IH initial abnormality (IH board initial abnormality)
  • Code: C472
  • Description: IH power voltage abnormality (power supply abnormality)
  • Code: C475
  • Description: IH power voltage abnormality (power supply abnormality when door is opened)
  • Code: C480
  • Description: Overheating of IGBT: The temperature of the IGBT rises abnormally.
  • Code: C490
  • Description: IH control circuit or IH coil abnormality: Abnormality is detected in IH control circuit or IH coil is broken/ shorted.
  • Code: C4B0
  • Description: Fuser unit counter abnormality
  • Code: C550
  • Description: RADF I/F error: Communication error has occurred between the RADF and the scanner.
  • Code: C570
  • Description: Communication error between Engine-CPU and IPC board
  • Code: C580
  • Description: Communication error between IPC board and finisher
  • Code: C900
  • Description: Connection error between SYS board and LGC board
  • Code: C940
  • Description: Engine-CPU abnormality
  • Code: C950
  • Description: LGC board memory abnormality
  • Code: C960
  • Description: Connection error between LGC board and DRV board, ID abnormality
  • Code: C970
  • Description: High-voltage transformer abnormality: Leakage of the main charger is detected.
  • Code: C9E0
  • Description: Connection error between SLG board and SYS board
  • Code: CA10
  • Description: Polygonal motor abnormality: The polygonal motor is not rotating normally.
  • Code: CA20
  • Description: H-Sync detection error: H-Sync signal detection PC board cannot detect laser beams.
  • Code: CB20
  • Description: Delivery motor abnormality: Delivery motor or delivery roller is not rotating normally. [MJ-1022]
  • Code: CB30
  • Description: Tray 1/Tray 2 shift motor abnormality: Tray 1/Tray 2 shift motor is not rotating or delivery tray is not moving normally. [MJ-1023/1024]
  • Code: CB40
  • Description: Rear aligning plate motor abnormality: Rear aligning plate motor is not rotating or aligning plate is not moving normally. [MJ-1023/1024]
  • Code: CB50
  • Description: Staple motor abnormality: Staple motor is not rotating or stapler is not moving normally. [MJ-1022/ 1023/1024]
  • Code: CB80
  • Description: Backup RAM data abnormality:
    1) Abnormality of checksum value on finisher controller PC board is detected when the power is turned ON. [MJ-1023/1024]
    2) Abnormality of checksum value on punch controller PC board is detected when the power is turned ON. [MJ-1023/1024 (when MJ-6004 is installed)]
  • Code: CB90
  • Description: Paper pushing plate motor abnormality: Paper pushing plate motor is not rotating or paper pushing plate is not moving normally. [MJ-1024]
  • Code: CBA0
  • Description: Stitch motor (front) abnormality: Stitch motor (front) is not rotating or rotary cam is not moving normally. [MJ-1024]
  • Code: CBB0
  • Description: Stitch motor (rear) abnormality: Stitch motor (rear) is not rotating or rotary cam is not moving normally. [MJ-1024]
  • Code: CBC0
  • Description: Alignment motor abnormality: Alignment motor is not rotating or aligning plate is not moving normally. [MJ-1024]
  • Code: CBD0
  • Description: Guide motor abnormality: Guide motor is not rotating or guide is not moving normally. [MJ-1024]
  • Code: CBE0
  • Description: Paper folding motor abnormality: Paper folding motor or paper folding roller is not rotating normally. [MJ-1024]
  • Code: CC00
  • Description: Sensor connector abnormality: Connector of guide home position sensor, paper pushing plate home position sensor or paper pushing plate top position sensor is disconnected. [MJ-1024]
  • Code: CC10
  • Description: Micro switch abnormality: With all covers closed, inlet door switch, delivery door switch or front cover switch is open. [MJ-1024]
  • Code: CC20
  • Description: Communication error between finisher and saddle stitcher: Communication error between finisher controller PC board and saddle stitcher controller board [MJ-1023/1024]
  • Code: CC30
  • Description: Stack processing motor abnormality: The stack processing motor is not rotating or the stack delivery belt is not moving normally. [MJ-1022]
  • Code: CC40
  • Description: Swing motor abnormality: Swing motor is not rotating or swing unit is not moving normally. [MJ-1023/ 1024]
  • Code: CC50
  • Description: Horizontal registration motor abnormality: Horizontal registration motor is not rotating or puncher is not shifting normally. [MJ-1023/1024 (when MJ- 6004 is installed)]
  • Code: CC60
  • Description: Punch motor abnormality: Punch motor is not rotating or puncher is not shifting normally. [MJ-1023/ 1024 (when MJ-6004 is installed)]
  • Code: CC80
  • Description: Front alignment motor abnormality: Front alignment motor is not rotating or front aligning plate is not moving normally. [MJ-1022] Front aligning plate motor abnormality: Front aligning plate motor is not rotating or aligning plate is not moving normally. [MJ-1023/1024]
  • Code: CC90
  • Description: Upper stack tray lift motor abnormality: The upper stack tray lift motor is not rotating or the upper stack tray is not moving normally. [MJ-1022]
  • Code: CCA0
  • Description: Lower stack tray lift motor abnormality: The lower stack tray lift motor is not rotating or the lower stack tray is not moving normally. [MJ-1022]
  • Code: CCB0
  • Description: Rear jogging motor abnormality: The rear jogging motor is not rotating or the rear jogging plate is not moving normally. [MJ-1022]
  • Code: CCD0
  • Description: Stack ejection motor abnormality: Stack ejection motor or stack ejection roller is not rotating normally. [MJ-1023/1024]
  • Code: CCE0
  • Description: Paper trailing edge assist motor abnormality: Paper trailing edge assist motor is not rotating or paper trailing edge assist is not moving normally. [MJ- 1023/1024]
  • Code: CCF0
  • Description: Gear changing motor abnormality: Gear changing motor is not rotating normally. [MJ-1023/1024]
  • Code: CE00
  • Description: Communication error between finisher and punch unit: Communication error between finisher controller PC board and punch controller PC board [MJ- 1023/1024 (when MJ-6004 is installed)]
  • Code: CE10
  • Description: Image quality sensor abnormality (OFF level): The output value of this sensor is out of a specified range when sensor light source is OFF.
  • Code: CE20
  • Description: Image quality sensor abnormality (no pattern level): The output value of this sensor is out of a specified range when the image quality control test pattern is not formed.
  • Code: CE40
  • Description: Image quality control test pattern abnormality: The test pattern is not formed normally.
  • Code: CE50
  • Description: Temperature/humidity sensor abnormality: The output value of this sensor is out of a specified range.
  • Code: CE90
  • Description: Drum thermistor abnormality: The output value of the drum thermistor is out of a specified range.
  • Code: CEA0
  • Description: Revolver home position detection abnormality: It cannot detect that the revolver is at its home position.
  • Code: CEB0
  • Description: Black developer unit lifting movement abnormality: The black developer unit does not move up or down normally (lifting cam does not operate normally).
  • Code: CEC0
  • Description: 2nd transfer roller position detection abnormality: The 2nd transfer roller does not contact/release normally.
  • Code: CEE0
  • Description: Transfer belt position detection abnormality (normal speed): The home position of the transfer belt cannot be detected.
  • Code: CEE1
  • Description: Transfer belt position detection abnormality (when decelerating): Reference position of the transfer belt cannot be detected.
  • Code: CEF0
  • Description: Revolver motor abnormality: Revolver motor is not rotating or revolver is not moving normally.
  • Code: CF20
  • Description: Toner density detection voltage abnormality: The output value of the color auto-toner sensor in printing is out of a specified range.
  • Code: CF30
  • Description: Reference plate detection voltage abnormality: The output value of the color auto-toner sensor against the reference plate is out of a specified range at the light amount correction during an auto-toner adjustment or when a print job has finished.
  • Code: CF30
  • Description: Reference plate detection voltage abnormality: The output value of the color auto-toner sensor against the reference plate is out of a specified range at the light amount correction during an auto-toner adjustment or when a print job has finished.
  • Code: CF40
  • Description: Light amount correction voltage abnormality: The light amount correction is not finished normally during an auto-toner adjustment or when a print job has finished, or the output value of the sensor is out of a specified range when the light amount correction has finished.
  • Code: CF50
  • Description: Color auto-toner sensor abnormality: The connection of the color auto-toner sensor cannot be detected at the initialization, or the output value of color auto-toner sensor when the revolver starts rotating for initialization is out of a specified range.
  • Code: E010
  • Description: Jam not reaching the exit sensor: The paper which has passed through the fuser unit does not reach the exit sensor.
  • Code: E020
  • Description: Stop jam at the exit sensor: The trailing edge of the paper does not pass the exit sensor after its leading edge has reached this sensor.
  • Code: E030
  • Description: Power-ON jam: The paper is remaining on the paper transport path when power is turned ON.
  • Code: E061
  • Description: Incorrect paper size setting for 1st drawer: The size of paper in the 1st drawer differs from size setting of the equipment.
  • Code: E062
  • Description: Incorrect paper size setting for 2nd drawer: The size of paper in the 2nd drawer differs from size setting of the equipment.
  • Code: E063
  • Description: Incorrect paper size setting for PFP upper drawer: The size of paper in the 3rd drawer differs from size setting of the equipment.
  • Code: E064
  • Description: Incorrect paper size setting for PFP lower drawer: The size of paper in the 4th drawer differs from size setting of the equipment.
  • Code: E065
  • Description: Incorrect paper size setting for bypass tray: The size of paper in the bypass tray differs from size setting of the equipment.
  • Code: E090
  • Description: Image data delay jam: Image data to be printed cannot be prepared
  • Code: E110
  • Description: ADU misfeeding (Paper not reaching the registration sensor): The paper which has passed through ADU does not reach the registration sensor during duplex printing.
  • Code: E120
  • Description: Bypass misfeeding (Paper not reaching the bypass feed sensor): Paper fed from the bypass tray does not reach the bypass feed sensor.
  • Code: E130
  • Description: 1st drawer misfeeding (Paper not reaching the 1st drawer feed sensor): The paper fed from the 1st drawer does not reach the 1st drawer feed sensor.
  • Code: E140
  • Description: 2nd drawer misfeeding (Paper not reaching the 2nd drawer feed sensor): The paper fed from the 2nd drawer does not reach the 2nd drawer feed sensor.
  • Code: E150
  • Description: PFP upper drawer misfeeding (Paper not reaching the PFP upper drawer feed sensor): The paper fed from the PFP upper drawer does not reach the PFP upper drawer feed sensor.
  • Code: E160
  • Description: PFP lower drawer misfeeding (Paper not reaching the PFP lower drawer feed sensor): The paper fed from the PFP lower drawer does not reach the PFP lower drawer feed sensor.
  • Code: E190
  • Description: LCF misfeeding (Paper not reaching the LCF feed sensor): The paper fed from the LCF does not reach the LCF feed sensor.
  • Code: E200
  • Description: 1st drawer transport jam (Paper not reaching the registration sensor): The paper does not reach the registration sensor after it has passed the 1st drawer feed sensor.
  • Code: E210
  • Description: 2nd drawer transport jam (Paper not reaching the registration sensor): The paper does not reach the registration sensor after it has passed the 1st drawer feed sensor.
  • Code: E220
  • Description: 2nd drawer transport jam (Paper not reaching the 1st drawer feed sensor): The paper does not reach the 1st drawer feed sensor after it has passed the 2nd drawer feed sensor.
  • Code: E300
  • Description: PFP upper drawer transport jam (Paper not reaching the registration sensor): The paper does not reach the registration sensor after it has passed the 1st drawer feed sensor.
  • Code: E310
  • Description: PFP upper drawer transport jam (Paper not reaching the 1st drawer feed sensor): The paper does not reach the 1st drawer feed sensor after it has passed the 2nd drawer feed sensor.
  • Code: E320
  • Description: PFP upper drawer transport jam (Paper not reaching the 2nd drawer feed sensor): The paper does not reach the 2nd drawer feed sensor after it has passed the PFP upper drawer feed sensor.
  • Code: E330
  • Description: PFP lower drawer transport jam (Paper not reaching the registration sensor): The paper does not reach the registration sensor after it has passed the 1st drawer feed sensor.
  • Code: E340
  • Description: PFP lower drawer transport jam (Paper not reaching the 1st drawer feed sensor): The paper does not reach the 1st drawer feed sensor after it has passed the 2nd drawer feed sensor.
  • Code: E350
  • Description: PFP lower drawer transport jam (Paper not reaching the 2nd drawer feed sensor): The paper does not reach the 2nd drawer feed sensor after it has passed the PFP upper drawer feed sensor.
  • Code: E360
  • Description: PFP lower drawer transport jam (Paper not reaching the PFP upper drawer feed sensor): The paper does not reach the PFP upper drawer feed sensor after it has passed the PFP lower drawer feed sensor.
  • Code: E400
  • Description: Jam access cover open jam: The jam access cover has opened during printing.
  • Code: E410
  • Description: Front cover open jam: The front cover has opened during printing.
  • Code: E420
  • Description: PFP side cover open jam: The PFP side cover has opened during printing.
  • Code: E430
  • Description: ADU open jam: The ADU has opened during printing.
  • Code: E440
  • Description: Side cover open jam: The side cover has opened during printing.
  • Code: E450
  • Description: LCF side cover open jam: The LCF side cover has opened during printing.
  • Code: E480
  • Description: Bridge unit open jam: The bridge unit has opened during printing.
  • Code: E510
  • Description: Jam not reaching the ADU entrance sensor: The paper does not reach the ADU entrance sensor after it is switchbacked in the exit section.
  • Code: E520
  • Description: Stop jam in the ADU: The paper does not reach the ADU exit sensor after it has passed the ADU entrance sensor.
  • Code: E550
  • Description: Paper remaining jam on the transport path: The paper is remaining on the transport path when printing is finished.
  • Code: E712
  • Description: Jam not reaching the original registration sensor: The original fed from the original feeding tray does not reach the original registration sensor
  • Code: E714
  • Description: Feed signal reception jam: The feed signal is received even no original exists on the original feeding tray.
  • Code: E721
  • Description: Jam not reaching the read sensor: The original does not reach the read sensor after it has passed the registration sensor (when scanning obverse side) or the reverse sensor (when scanning reverse side).
  • Code: E722
  • Description: Jam not reaching the original exit/reverse sensor (during scanning): The original which passed the read sensor does not reach the original exit/reverse sensor when it is transported from the scanning section to exit section.
  • Code: E724
  • Description: Stop jam at the original registration sensor: The trailing edge of the original does not pass the original registration sensor after its leading edge has reached this sensor.
  • Code: E725
  • Description: Stop jam at the read sensor: The trailing edge of the original does not pass the read sensor after its leading edge has reached this sensor.
  • Code: E731
  • Description: Stop jam at the original exit/reverse sensor: The trailing edge of the original does not pass the original exit/reverse sensor after its leading edge has reached this sensor.
  • Code: E860
  • Description: RADF jam access cover open: The RADF jam access cover has opened during RADF operation.
  • Code: E870
  • Description: RADF open jam: RADF has opened during RADF operation
  • Code: E871
  • Description: Cover open jam in the read ready status
  • Code: E910
  • Description: Jam at the bridge unit transport sensor 1: The paper does not reach the bridge unit transport sensor 1 after it has passed the exit sensor.
  • Code: E920
  • Description: Stop jam at the bridge unit transport sensor 1: The trailing edge of the paper does not pass the bridge unit transport sensor 1 after its leading edge has reached the sensor.
  • Code: E930
  • Description: Jam at the bridge unit transport sensor 2: The trailing edge of the paper does not reach the bridge unit transport sensor 2 after its leading edge has reached the bridge unit transport sensor 1.
  • Code: E940
  • Description: Stop jam at the bridge unit transport sensor 2: The trailing edge of the paper does not pass the bridge unit transport sensor 2 after its leading edge has reached the bridge unit transport sensor 2.
  • Code: E9F0
  • Description: Punching jam: Punching is not performed properly.
  • Code: EA10
  • Description: Paper transport delay jam: The paper which has passed the bridge unit does not reach the inlet sensor.[MJ-1031/1101] The paper which has passed the bridge unit does not reach the inlet sensor.
  • Code: EA20
  • Description: Paper transport stop jam: The paper does not pass through the inlet sensor. The paper which has passed through the inlet sensor does not reach the feeding sensor.
  • Code: EA30
  • Description: Power-ON jam: Paper exists at the inlet sensor when power is turned ON.
  • Code: EA40
  • Description: Joint open jam: The finisher cover opened during machine operation. Cover open error: The front cover or stationary tray is opened during paper transport.
  • Code: EA50
  • Description: Stapling jam: Stapling is not performed properly.
  • Code: EA60
  • Description: Early arrival jam: The inlet sensor detects the paper earlier than a specified timing.
  • Code: EA70
  • Description: Stack exit belt home position error: The stack exit belt is not at the home position. Stack slider home position error: The stack slider is not at the home position.
  • Code: EA80
  • Description: Stapling jam: Stapling is not performed properly. [MJ-1024]
  • Code: EA90
  • Description: Door open jam: The delivery cover or inlet cover has opened dur-ing printing [MJ-1024].
  • Code: EAA0
  • Description: Power-ON jam: Paper exists at No.1 paper sensor, No. 2 paper sensor, No.3 paper sensor, vertical path paper sensor or delivery sensor when power is turned ON. [MJ-1024]
  • Code: EAB0
  • Description: Transport stop jam: The paper which passed through the inlet sensor does not reach or pass No.1 paper sensor, No. 2 paper sensor, No.3 paper sensor or delivery sensor. [MJ-1024]
  • Code: EAC0
  • Description: Transport delay jam: The paper which has reached the inlet sensor does not pass through the inlet sensor. [MJ-1024]
  • Code: EAD0
  • Description: Print end command time-out jam: The printing has not finished normally because of the communication error between the SYS board and LGC board at the end of printing.
  • Code: EAE0
  • Description: Receiving time time-out jam: The printing has been interrupted because of the communication error between the equipment and finisher when the paper is transported from the equipment to the finisher.
  • Code: EAF0
  • Description: Stack return jam: It cannot load the paper which passed through the delivery roller on the intermediary process tray. [MJ-1022]
  • Code: EB50
  • Description: Paper remaining on the transport path: The multiple feeding of preceding paper caused the misfeeding of upcoming paper.
  • Code: EB60
  • Description: Paper remaining on the transport path: The multiple feeding of preceding paper caused the misfeeding of upcoming paper (redetection after no jam is detected at [EB50]).
  • Code: F070
  • Description: Communication error between System-CPU and Engine-CPU
  • Code: F090
  • Description: SRAM abnormality on the SYS board
  • Code: F091
  • Description: NVRAM abnormality on the SYS board
  • Code: F092
  • Description: SRAM and NVRAM abnormality on the SYS board
  • Code: F100
  • Description: HDD format error: HDD cannot be initialized normally.
  • Code: F101
  • Description: HDD unmounted: Connection of HDD cannot be detected.
  • Code: F102
  • Description: HDD start error: HDD cannot become ‘Ready’ state.
  • Code: F103
  • Description: HDD transfer time-out: Reading/writing cannot be performed in the specified period of time.
  • Code: F104
  • Description: HDD data error: Abnormality is detected in the data of HDD.
  • Code: F105
  • Description: HDD other error
  • Code: F106
  • Description: Point and Print partition damage
  • Code: F107
  • Description: /BOX partition damage
  • Code: F108
  • Description: /SHA partition damage
  • Code: F110
  • Description: Communication error between System-CPU and Scanner-CPU
  • Code: F111
  • Description: Scanner response abnormality
  • Code: F120
  • Description: Database abnormality: Database is not operating normally.
  • Code: F130
  • Description: Invalid MAC address
  • Code: F200
  • Description: Data overwrite kit (GP-1060) is taken off
  • Code: F350
  • Description: SLG board abnormality

МФУ SHARP
МФУ TOSHIBA
BCP TOSHIBA
Совместимые картриджи G&G

Поиск по каталогу:

Наименование


Empty cart
Корзина пуста

 МЫ ПРЕДЛАГАЕМ СПЕЦИАЛЬНЫЕ УСЛОВИЯ СОТРУДНИЧЕСТВА ДЛЯ КОРПОРАТИВНЫХ КЛИЕНТОВ И СЕРВИСНЫХ ЦЕНТРОВ