Toshiba e-Studio 280 Коды ошибок

  • Code: C010
  • Description: Drive system related service call
    Main motor abnormality: The main motor is not rotating normally.
  • Code: C040
  • Description: PFP motor abnormality: The PFP motor is not rotating normally.
  • Code: C130
  • Description: Upper drawer tray abnormality: The upper drawer tray motor is not rotating or the upper drawer tray is not moving normally.
  • Code: C140
  • Description: Lower drawer tray abnormality: The lower drawer tray motor is not rotating or the lower drawer tray is not moving normally.
  • Code: C150
  • Description: PFP upper drawer tray abnormality: The PFP upper drawer tray motor is not rotating or the PFP upper drawer tray is not moving normally.
  • Code: C160
  • Description: PFP lower drawer tray abnormality: The PFP lower drawer tray motor is not rotating or the PFP lower drawer tray is not moving normally.
  • Code: C180
  • Description: LCF tray-up motor abnormality: The LCF tray-up motor is not rotating or the LCF tray is not moving normally.
  • Code: C1A0
  • Description: LCF end fence motor abnormality: The LCF end fence motor is not rotating or the LCF end fence is not moving normally.
  • Code: C1B0
  • Description: LCF transport motor abnormality: The LCF transport motor is not rotating normally.
  • Code: C260
  • Description: Peak detection error: Lighting of the exposure lamp (white reference) is not detected when power is turned ON.
  • Code: C270
  • Description: Carriage home position sensor not turning OFF within a specified period of time: The carriage does not shift from its home position in a specified period of time.
  • Code: C280
  • Description: Carriage home position sensor not turning ON within a specified period of time: The carriage does not reach to its home position in a specified period of time.
  • Code: C410
  • Description: Thermistor or heater abnormality at power-ON: Abnormality of service call the thermistor is detected when power is turned ON or the temperature of the fuser roller does not rise in a specified period of time after power is turned ON.
  • Code: C440
  • Description: Heater abnormality after abnormality judgment: The temperature of the fuser roller has exceeded the range of control (in this case, the main switch turns OFF automatically) or does not even reach the range.
  • Code: C450
  • Description: Thermistor abnormality during printing: Abnormality of the thermistor is detected during printing.
  • Code: C550, C780
  • Description: RADF I/F error: Communication error has occurred between the RADF and the scanner.
  • Code: C570
  • Description: Communication error between Engine-CPU and IPC board
  • Code: C580
  • Description: Communication error between IPC board and finisher
  • Code: C730
  • Description: EEPROM initialization error: EEPROM is not initialized normally when performing the code 05-356.
  • Code: C810
  • Description: Fan motor abnormality: The fan motor is not rotating normally.
  • Code: C820
  • Description: Read sensor adjustment error: The read sensor cannot be adjusted normally when performing the code 05-356
  • Code: C830
  • Description: Original length sensor adjustment error: The original length sensor cannot be adjusted normally when performing the code 05-356.
  • Code: C940
  • Description: Circuit related service call
    Engine-CPU abnormality
  • Code: C970
  • Description: Process related service call
    High-voltage transformer abnormality: Leakage of the main charger is detected.
  • Code: CA10
  • Description: Polygonal motor abnormality: The polygonal motor is not rotating normally.
  • Code: CA20
  • Description: H-Sync detection error: H-Sync detection PC board cannot detect laser beams.
  • Code: CB10
  • Description: Transport motor abnormality: The transport motor or stack transport roller is not rotating normally. [MJ-1025]
  • Code: CB20
  • Description: Delivery motor abnormality: Delivery motor or delivery roller is not rotating normally. [MJ-1022/1025]
  • Code: CB30
  • Description: Tray lift motor abnormality: The tray lift motor is not rotating normally or the delivery tray is not moving normally. [MJ-1025]
  • Code: CB50
  • Description: Staple motor (staple/fold) abnormality: The staple motor is not rotating normally or the stapler is not moving normally. [MJ-1025]
  • Code: CB60
  • Description: Stapler unit shift motor abnormality: The stapler unit shift motor is not rotating normally or the Stapler Unit is not moving normally. [MJ-1025]
  • Code: CB80
  • Description: Backup RAM data abnormality:
    1) Abnormality of checksum value on finisher controller board is detected when the power is turned on. [MJ-1025]
    2) Abnormality of checksum value on punch controller board is detected when the power is turned on. [MJ-1025 (when MJ-6005 is installed)]
  • Code: CC30
  • Description: Stack processing motor abnormality: The stack processing motor is not rotating normally or the stack delivery belt is not moving normally. [MJ-1022] Paddle motor abnormality: The paddle motor is not rotating normally or the swing guide is not moving normally. [MJ-1025]
  • Code: CC50
  • Description: Horizontal registration motor abnormality: The horizontal registration motor is not rotating normally or the puncher is not moving normally. [MJ-1025 (when MJ-6005 is installed)]
  • Code: CC60
  • Description: Punch motor abnormality: The punch motor is not rotating normally or the puncher is not moving normally. [MJ-1025 (when MJ-6005 is installed)]
  • Code: CC80
  • Description: Front jogging motor abnormality: Front jogging motor is not rotating normally or the front alignment plate is not moving normally. [MJ-1022] Alignment motor (front) abnormality: The alignment motor (front) is not rotating normally or the front alignment plate is not moving normally. [MJ-1025]
  • Code: CC90
  • Description: Upper stack tray lift motor abnormality: The upper stack tray lift motor is not rotating or the upper stack tray is not moving normally. [MJ-1022]
  • Code: CCA0
  • Description: Lower stack tray lift motor abnormality: The lower stack tray lift motor is not rotating or the lower stack tray is not moving normally. [MJ-1022]
  • Code: CCB0
  • Description: Rear jogging motor abnormality: Rear jogging motor is not rotating normally or the rear alignment plate is not moving normally. [MJ-1022] Alignment motor (rear) abnormality: The alignment motor (rear) is not rotating normally or the rear alignment plate is not moving normally. [MJ-1025]
  • Code: CDC0
  • Description: Punch power failure abnormality: 24 V is not applied to the punch controller board. [MJ-1025 (when MJ-6005 is installed)]
  • Code: CDD0
  • Description: Folding position sensor abnormality: Automatic adjustment of the folding position sensor can not be performed properly. [MJ-1025]
  • Code: CDE0
  • Description: Paddle motor abnormality: The paddle motor does not rotate properly. [MJ-1025]
  • Code: CDF0
  • Description: Initialization error of the offset tray: The home position of the separator cannot be detected when the power is turned ON.
  • Code: CE00
  • Description: Communication error between finisher unit and puncher unit: Communication error between the finisher controller PC board and punch controller PC board. [MJ-1025 (when MJ-6005 is installed)]
  • Code: CF60
  • Description: Toner for recycle transport area lock
  • Code: E010
  • Description: Jam not reaching the exit sensor: The paper which has passed through the fuser unit does not reach the exit sensor.
  • Code: E020
  • Description: Stop jam at the exit sensor: The trailing edge of the paper does not pass the exit sensor after its leading edge has reached this sensor.
  • Code: E030
  • Description: Power-ON jam: The paper is remaining on the paper transport path when power is turned ON.
  • Code: E090
  • Description: HDD abnormality causes jam: Image data to be printed cannot be prepared.
  • Code: E110
  • Description: ADU misfeeding (Paper not reaching the 1st transport sensor): The paper which has passed through ADU does not reach the 1st transport sensor during duplex printing.
  • Code: E120
  • Description: Bypass misfeeding (Paper not reaching the 1st transport sensor): The paper fed from the bypass tray does not reach the 1st transport sensor.
  • Code: E130
  • Description: Upper drawer misfeeding (Paper not reaching the 1st transport sensor): The paper fed from the upper drawer does not reach the 1st transport sensor.
  • Code: E140
  • Description: Lower drawer misfeeding (Paper not reaching the 2nd transport sensor): The paper fed from the lower drawer does not reach the 2nd transport sensor.
  • Code: E150
  • Description: PFP upper drawer misfeeding (Paper not reaching the PFP upper drawer feed sensor): The paper fed from the PFP upper drawer does not reach the PFP upper drawer feed sensor
  • Code: E160
  • Description: PFP lower drawer misfeeding (Paper not reaching the PFP lower drawer feed sensor): The paper fed from the PFP lower drawer does not reach the PFP lower drawer feed sensor.
  • Code: E190
  • Description: LCF misfeeding (Paper not reaching the LCF feed sensor): The paper fed from the LCF does not reach the LCF feed sensor
  • Code: E200
  • Description: Upper drawer transport jam (Paper not reaching the registration sensor): The paper does not reach the registration sensor after it has passed the 1st transport sensor.
  • Code: E210
  • Description: Lower drawer transport jam (Paper not reaching the registration sensor): The paper does not reach the registration sensor after it has passed the 1st transport sensor.
  • Code: E220
  • Description: Lower drawer transport jam (Paper not reaching the 1st transport sensor): The paper does not reach the 1st transport sensor after it has passed the lower drawer feed sensor.
  • Code: E270
  • Description: Bypass transport jam (paper not reaching the registration sensor): The paper does not reach the registration sensor after it has passed the 1st transport sensor.
  • Code: E280
  • Description: ADU transport jam (paper not reaching the registration sensor): The paper which has passed through ADU and the 1st transport sensor does not reach the registration sensor during duplex printing.
  • Code: E300
  • Description: PFP upper drawer transport jam (Paper not reaching the registration sensor): The paper does not reach the registration sensor after it has passed the 1st transport sensor.
  • Code: E310
  • Description: PFP upper drawer transport jam (Paper not reaching the 1st transport sensor): The paper does not reach the 1st transport sensor after it has passed the 2nd transport sensor.
  • Code: E320
  • Description: PFP upper drawer transport jam (Paper not reaching the 2nd transport sensor): The paper does not reach the 2nd transport sensor after it has passed the PFP upper drawer feed sensor.
  • Code: E330
  • Description: PFP lower drawer transport jam (Paper not reaching the registration sensor): The paper does not reach the registration sensor after it has passed the 1st transport sensor.
  • Code: E340
  • Description: PFP lower drawer transport jam (Paper not reaching the 1st transport sensor): The paper does not reach the 1st transport sensor after it has passed the PFP lower drawer feed sensor.
  • Code: E350
  • Description: PFP lower drawer transport jam (Paper not reaching the 2nd transport sensor): The paper does not reach the 2nd transport sensor after it has passed the PFP upper drawer feed sensor.
  • Code: E360
  • Description: PFP lower drawer transport jam (Paper not reaching the PFP upper drawer feed sensor): The paper does not reach the PFP upper drawer feed sensor after it has passed the PFP lower drawer feed sensor.
  • Code: E3C0
  • Description: LCF transport jam (Paper not reaching the registration sensor): The paper does not reach the registration sensor after it has passed the 1st transport sensor.
  • Code: E3D0
  • Description: LCF transport jam (Paper not reaching the 1st transport sensor): The paper does not reach the 1st transport sensor after it has passed the 2nd transport sensor.
  • Code: E3E0
  • Description: LCF transport jam (Paper not reaching the 2nd transport sensor): The paper does not reach the 2nd transport sensor after it has passed the LCF feed sensor
  • Code: E400
  • Description: Transfer cover open jam: The transfer cover has opened during printing.
  • Code: E410
  • Description: Front cover open jam: The front cover has opened during printing.
  • Code: E420
  • Description: PFP side cover open jam: The PFP side cover has opened during printing.
  • Code: E430
  • Description: ADU open jam: The ADU has opened during printing.
  • Code: E440
  • Description: Side cover open jam: The side cover has opened during printing.
  • Code: E450
  • Description: LCF side cover open jam: The LCF side cover has opened during printing.
  • Code: E480
  • Description: Bridge unit open jam: The bridge unit has opened during printing.
  • Code: E490
  • Description: Job separator cover open jam: The job separator cover has opened during printing.
  • Code: E491
  • Description: Offset tray cover open jam: The offset tray cover has opened during printing.
  • Code: E510
  • Description: Stop jam in the ADU: The paper does not reach the ADU exit sensor after it has passed the ADU entrance sensor.
  • Code: E520
  • Description: Jam not reaching the ADU entrance sensor: The paper does not reach the ADU entrance sensor after it is switchbacked in the exit section.
  • Code: E550
  • Description: Paper remaining jam on the transport path: The paper is remaining on the transport path when printing is finished (caused by a multiple paper feeding).
  • Code: E711
  • Description: Jam not reaching the original length sensor: The original fed from the original feeding tray does not reach the original length sensor.
  • Code: E712
  • Description: Jam not reaching the registration sensor: The original fed from the original feeding tray does not reach the registration sensor.
  • Code: E713
  • Description: Stop jam at the original length sensor: The trailing edge of the original does not pass the original length sensor after its leading edge has reached this sensor.
  • Code: E714
  • Description: Feed signal reception jam: The feed signal is received even no original exists on the original feeding tray.
  • Code: E721
  • Description: Jam not reaching the read sensor: The original does not reach the read sensor after it has passed the registration sensor (when scanning obverse side) or the reverse sensor (when scanning reverse side).
  • Code: E722
  • Description: Jam not reaching the exit sensor (during scanning): The original which passed the read sensor does not reach the exit sensor when it is transported from the scanning section to exit section.
  • Code: E723
  • Description: Jam not reaching the reverse sensor (during scanning): The original which passed the read sensor does not reach the reverse sensor when it is transported from the scanning section to reverse section.
  • Code: E724
  • Description: Stop jam at the registration sensor: The trailing edge of the original does not pass the registration sensor after its leading edge has reached this sensor.
  • Code: E725
  • Description: Stop jam at the read sensor: The trailing edge of the original does not pass the read sensor after its leading edge has reached this sensor.
  • Code: E726
  • Description: Transport/exit signal reception jam: RADF receives the transport/exit reception signal from the equipment when no original is at the exposure waiting position.
  • Code: E731
  • Description: Stop jam at the exit sensor: The trailing edge of the original does not pass the exit sensor after its leading edge has reached this sensor.
  • Code: E741
  • Description: Stop jam at the reverse sensor: The trailing edge of the original does not pass the reversal sensor after its leading edge has reached this sensor.
  • Code: E742
  • Description: Jam not reaching the reverse sensor (during reverse feeding): The leading edge of the original does not reach the reverse sensor when original is fed from the reverse section.
  • Code: E743
  • Description: Jam not reaching the exit sensor (during reverse feeding): The original does not reach the exit sensor after it has passed the reverse sensor when the original is exited from the reverse section.
  • Code: E860
  • Description: RADF jam access cover open: The RADF jam access cover has opened during RADF operation.
  • Code: E870
  • Description: RADF open jam: RADF has opened during RADF operation.
  • Code: E910
  • Description: Jam at the bridge unit transport sensor-1: The paper does not reach the bridge unit transport sensor- 1 after it has passed the exit sensor.
  • Code: E920
  • Description: Stop jam at the bridge unit transport sensor-1: The trailing edge of the paper does not pass the bridge unit transport sensor-1 after its leading edge has reached the sensor.
  • Code: E930
  • Description: Jam at the bridge unit transport sensor-2: The trailing edge of the paper does not reach the bridge unit transport sensor-2 after its leading edge has reached the bridge unit transport sensor-1.
  • Code: E940
  • Description: Stop jam at the bridge unit transport sensor-2: The trailing edge of the paper does not reach the bridge unit transport sensor-2 after its leading edge has reached the bridge unit transport sensor-2.
  • Code: E950
  • Description: Jam not reaching the job separator transport sensor: The paper has passed through the exit sensor does not reach the job separator transport sensor.
  • Code: E951
  • Description: Stop jam at the job separator transport sensor: The trailing edge of the paper does not pass the job separator transport sensor.
  • Code: E960
  • Description: Jam not reaching the offset tray transport sensor: The paper has passed through the exit sensor does not reach the offset tray transport sensor.
  • Code: E961
  • Description: Stop jam at the offset tray transport sensor: The trailing edge of the paper does not pass the offset tray transport sensor.
  • Code: E9F0
  • Description: Finisher jam (Puncher unit)
    Punching jam: Punching is not performed properly. [MJ-1025 (When MJ-6005 is installed)]
  • Code: EA10
  • Description: Paper transport delay jam: The paper which has passed the bridge unit does not reach the inlet sensor. [MJ-1022/1025]
  • Code: EA20
  • Description: Paper transport stop jam: The paper does not pass through the inlet sensor. [MJ-1022/1025]
  • Code: EA30
  • Description: Power-ON jam: Paper exists at the inlet sensor when power is turned ON. [MJ-1022/1025]
  • Code: EA40
  • Description: Door open jam: The finisher has been released from the equipment during printing. [MJ-1022/1025]
  • Code: EA50
  • Description: Stapling jam: Stapling is not performed properly. [MJ-1022/1025]
  • Code: EA60
  • Description: Early arrival jam: The inlet sensor detects the paper earlier than a specified timing. [MJ-1022]
  • Code: EA70
  • Description: Stack delivery jam: It cannot deliver the stack of paper on the intermediary process tray to the stack tray. [MJ-1022/1025]
  • Code: EAB0
  • Description: Saddle paper transport stop jam: The paper which passed through the inlet sensor does not reach or pass through the folding position sensor. [MJ-1025]
  • Code: EAC0
  • Description: Saddle transport delay jam: The paper which has reached the inlet sensor does not pass through this sensor. [MJ-1025]
  • Code: EAD0
  • Description: Other paper jam
    Print end command time-out jam: The printing has not finished normally because of the communication error between the SYS board and LGC board at the end of printing.
  • Code: EAE0
  • Description: Receiving time time-out jam: The printing has been interrupted because of the communication error between the equipment and finisher when the paper is transported from the equipment to the finisher.
  • Code: EAF0
  • Description: Stack return jam: It cannot load the paper which passed through the delivery roller on the intermediary process tray. [MJ-1022]
  • Code: EB30
  • Description: Ready time time-out jam: The equipment judges that the paper transport to the finisher is disabled because of the communication error between the equipment and finisher at the start of printing.
  • Code: EB50
  • Description: Paper remaining on the transport path: The multiple feeding of preceding paper caused the misfeeding of upcoming paper.
  • Code: EB60
  • Description: Paper remaining on the transport path: The multiple feeding of preceding paper caused the misfeeding of upcoming paper (redetection after no jam is detected at [EB50]).
  • Code: F070
  • Description: Communication error between System-CPU and Engine- CPU
  • Code: F090
  • Description: SRAM abnormality on the SYS board
  • Code: F091
  • Description: NVRAM abnormality on the SYS board
  • Code: F092
  • Description: SRAM and NVRAM abnormality on the SYS board
  • Code: F100
  • Description: HDD format error: HDD cannot be initialized normally.
  • Code: F101
  • Description: HDD unmounted: Connection of HDD cannot be detected.
  • Code: F102
  • Description: HDD start error: HDD cannot become ‘Ready’ state.
  • Code: F103
  • Description: HDD transfer time-out: Reading/writing cannot be performed in the specified period of time.
  • Code: F104
  • Description: HDD data error: Abnormality is detected in the data of HDD.
  • Code: F105
  • Description: HDD other error
  • Code: F106
  • Description: Point and Print partition damage
  • Code: F107
  • Description: SHR partition damage
  • Code: F108
  • Description: SHA partition damage
  • Code: F110
  • Description: Communication error between System-CPU and Scanner- CPU
  • Code: F111
  • Description: Scanner response abnormality
  • Code: F120
  • Description: Database abnormality: Database is not operating normally.
  • Code: F130
  • Description: Invaid MAC address
  • Code: F200
  • Description: Data overwrite kit (GP-1050/1060) is taken off

МФУ TOSHIBA
Печать этикеток TOSHIBA
Совместимые картриджи G&G

Поиск по каталогу:

Наименование


Empty cart
Корзина пуста

 МЫ ПРЕДЛАГАЕМ СПЕЦИАЛЬНЫЕ УСЛОВИЯ СОТРУДНИЧЕСТВА ДЛЯ КОРПОРАТИВНЫХ КЛИЕНТОВ И СЕРВИСНЫХ ЦЕНТРОВ