Toshiba e-Studio 2555C Коды ошибок

  • Code: C020
  • Description: Developer drive motor abnormality: Thedeveloper drive motor is not rotating normally.
  • Code: C040
  • Description: PFP motor abnormality: The PFP motor is not rotating normally. (the case that paper can be fed from any drawer except the PFP)
  • Code: C130
  • Description: 1st drawer tray abnormality: The tray-up motor is not rotating or the 1st drawer tray is not moving normally. (the case that paper can be fed from any drawer except the 1st drawer)
  • Code: C140
  • Description: 2nd drawer tray abnormality: The tray-up motor is not rotating or the 2nd drawer tray is not moving normally. (the case that paper can be fed from any drawer except the 2nd drawer)
  • Code: C150
  • Description: PFP upper drawer tray abnormality: The PFP upper drawer tray-up motor is not rotating or the PFP upper drawer tray is not moving normally. (the case that paper can be fed from any drawer except the PFP upper drawer)
  • Code: C160
  • Description: PFP lower drawer tray abnormality: The PFP lower drawer tray-up motor is not rotating or the PFP lower drawer tray is not moving normally. (the case that paper can be fed from any drawer except the PFP lower drawer)
  • Code: C180
  • Description: LCF tray-up motor abnormality: The LCF tray- up motor is not rotating or the LCF tray is not moving normally. (the case that paper can be fed from any drawer except the LCF)
  • Code: C1A0
  • Description: LCF end fence motor abnormality: The LCF end fence motor is not rotating or the LCF end fence is not moving normally. (the case that paper can be fed from any drawer except the LCF)
  • Code: C1B0
  • Description: LCF transport motor abnormality: The LCF transport motor is not rotating normally (when paper can be fed from any drawer except the LCF).
  • Code: C260
  • Description: Peak detection error: Lighting of the exposure lamp (white reference) is not detected when power is turned ON, or communication error with CCD board.
  • Code: C270
  • Description: Carriage home position sensor not turning OFF within a specified period of time: The carriage does not shift from its home position in a specified time.
  • Code: C280
  • Description: Carriage home position sensor not going ONwithin a specified time
  • Code: C290
  • Description: Scanner fuse blowout: 24V power for the scanning system is not supplied at the scanner warming-up after power-ON.
  • Code: C370
  • Description: Drum TBU motor abnormality
  • Code: C380
  • Description: Auto-toner sensor-K abnormality (upper limit)
  • Code: C381
  • Description: Auto-toner sensor-K abnormality (lower limit)
  • Code: C390
  • Description: Auto-toner sensor-C abnormality (upper limit)
  • Code: C391
  • Description: Auto-toner sensor-C abnormality (lower limit)
  • Code: C3A0
  • Description: Auto-toner sensor-M abnormality (upper limit)
  • Code: C3A1
  • Description: Auto-toner sensor-M abnormality (lower limit)
  • Code: C3B0
  • Description: Auto-toner sensor-Y abnormality (upper limit)
  • Code: C3B1
  • Description: Auto-toner sensor-Y abnormality (lower limit)
  • Code: C3E0
  • Description: Developer unit replacement (old-new)detection abnormality
  • Code: C3E1
  • Description: Drum/cleaner/charger unit replacement (old- new) detection abnormality
  • Code: C445
  • Description: IH coil abnormality after abnormality judgment(pre-running end temperature abnormality)
  • Code: C446
  • Description: IH coil abnormality after abnormality judgment(pre-running end temperature abnormality)
  • Code: C447
  • Description: IH coil abnormality after abnormality judgment(temperature abnormality at ready status)
  • Code: C449
  • Description: IH coil abnormality after abnormality judgment(temperature abnormality at high temperature)
  • Code: C471
  • Description: IH board initialization abnormality
  • Code: C472
  • Description: Power supply abnormality
  • Code: C473
  • Description: Surge pressure detection / power and voltage upper limit abnormality
  • Code: C474
  • Description: Power and voltage lower limit abnormality
  • Code: C475
  • Description: IH power voltage abnormality (power supply abnormality when door is opened)
  • Code: C480
  • Description: IGBT high temperature abnormality
  • Code: C481
  • Description: IGBT thermistor breaking abnormality
  • Code: C4B0
  • Description: Fuser unit counter abnormality
  • Code: C4B1
  • Description: Fuser unit voltage judgment abnormality
  • Code: C4C0
  • Description: Fuser unit new/old detection fuse abnormality
  • Code: C4D0
  • Description: Fuser thermistor abnormality
  • Code: C4E0
  • Description: Fuser pressure roller release abnormality - Though the pressure roller is released, its position cannot be detected.
  • Code: C4E1
  • Description: Fuser pressure roller contact/semi-contact abnormality - Though the pressure roller is contacted, its position cannot be detected.
  • Code: C4E2
  • Description: Fuser belt rotation detection sensor abnormality - The fuser belt does not rotate or incorrectly rotates.
  • Code: C550
  • Description: RADF I/F error: Communication error has occurred between the RADF and the scanner.
  • Code: C551
  • Description: RADF model detection error
  • Code: C560
  • Description: Communication error between Engine-CPUs
  • Code: C580
  • Description: Communication error between LGC board and finisher
  • Code: C5A0
  • Description: EEPROM not connected (LGC board)
  • Code: C5A1
  • Description: EEPROM data abnormality (LGC board)
  • Code: C8E0
  • Description: RADF communication protocol abnormality: The system has to be stopped because the control
  • Code: C900
  • Description: Connection error between SYS board andLGC board
  • Code: C911
  • Description: Toner cartridge IC chip access board abnormality
  • Code: C940
  • Description: Engine-CPU abnormality
  • Code: C962
  • Description: LGC board ID abnormality
  • Code: C964
  • Description: LGC board boot process abnormality
  • Code: C970
  • Description: High-voltage transformer abnormality: Leakage of the main charger is detected.
  • Code: C9E0
  • Description: Connection error between scanner CPU and system CPU
  • Code: CA00
  • Description: color registration abnormality
  • Code: CB00
  • Description: Finisher not connected: Communication error has occurred between the equipment and finisher. [MJ-1107/1108]
  • Code: CB01
  • Description: Finisher communication error [MJ-1036] Finisher communication error: Communication error has occurred between the equipment and finisher. [MJ-1107/1108]
  • Code: CB10
  • Description: Entrance motor abnormality: The entrance motor is not rotating normally. [MJ-1107/1108]
  • Code: CB11
  • Description: Buffer tray guide motor abnormality: The buffer tray guide motor is not rotating or the buffer tray guide is not moving normally. [MJ-1107/1108]
  • Code: CB12
  • Description: Buffer roller drive motor abnormality: The buffer roller drive motor is not rotating or the buffer roller is not moving normally. [MJ-1107/1108]
  • Code: CB13
  • Description: Finisher exit motor abnormality [MJ-1108]
  • Code: CB14
  • Description: Paper holding arm motor abnormality [MJ-1108]
  • Code: CB30
  • Description: Movable tray shift motor abnormality: The movable tray shift motor or the movable tray does not work properly. [MJ-1036]Movable tray shift motor abnormality: The movable tray shift motor is not rotating or the movable tray is not moving normally. [MJ-1107/1108]
  • Code: CB31
  • Description: Movable tray paper-full detection error: The actuator of the movable tray paper-full detection sensor does not move smoothly. [MJ-1107/1108]
  • Code: CB40
  • Description: Front alignment plate home position detection error: The detection of the home position ends abnormally because the front alignment plate has not worked properly.[MJ-1036]Front alignment motor abnormality: The front alignment motor is not rotating or the front alignment plate is not moving normally. [MJ-1107/1108]
  • Code: CB50
  • Description: Stapler unit home position detection error: The detection of the home position of the stapler unit ends abnormally. [MJ-1036]Stapler home position error: The stapler home position sensor does not work. [MJ-1107/1108]
  • Code: CB51
  • Description: Stapler unit sliding home position detection error: The detection of the home position of the stapler unit sliding ends abnormally. [MJ-1036]Stapler shift home position error: The stapler is not at the home position. [MJ-1107/1108]
  • Code: CB60
  • Description: Stapler shift motor abnormality: Stapler shift motor is not rotating or staple unit is not moving normally. [MJ-1107/1108]
  • Code: CB80
  • Description: Finisher control PC board (FIN) backup RAM error: An error occurs during the writing of data into the EEPROM of the Finisher. [MJ-1036]Backup RAM data abnormality: Abnormality of checksum value on finisher controller PC board is detected when the power is turned ON. [MJ-1107/1108]
  • Code: CB81
  • Description: Flash ROM abnormality: Abnormality of checksum value on finisher controller PC board is detected when the power is turned ON. [MJ-1107/1108]
  • Code: CB82
  • Description: Finisher - Main CPU program error [MJ-1107/1108]
  • Code: CB83
  • Description: Saddle Stitch Finisher - Main CPU program error [MJ-1108]
  • Code: CB84
  • Description: Hole Punch Unit - Main CPU program error[MJ-1107/1108/6104]
  • Code: CB91
  • Description: Saddle Stitch Finisher flash ROM abnormality[MJ-1108]
  • Code: CB92
  • Description: Saddle Stitch Finisher RAM abnormality [MJ-1108]
  • Code: CB93
  • Description: Additional folding motor abnormality [MJ-1108]
  • Code: CB94
  • Description: Saddle transport motor abnormality [MJ-1108]
  • Code: CB95
  • Description: Stacker motor abnormality [MJ-1108]
  • Code: CBA0
  • Description: Front saddle stapler home position error: The stapler home position detection is abnormally operated and finished. [MJ-1108]
  • Code: CBB0
  • Description: Rear saddle stapler home position error: The stapler home position detection is abnormally operated and finished. [MJ-1108]
  • Code: CBE0
  • Description: Saddle Stitch Finisher folding motor (M17) abnormality: The folding motor is not rotating or the folding roller is not moving normally. [MJ-1108]
  • Code: CC02
  • Description: Stack exit roller nip home position detection error [MJ-1036]
  • Code: CC20
  • Description: Saddle communication error [MJ-1108]
  • Code: CC30
  • Description: Stack transport motor abnormality: The stack transport motor is not rotating or the stack transport belt is not moving normally. [MJ-1107/1108]
  • Code: CC31
  • Description: Transport motor abnormality: The transport motor is not rotating or the stack transport roller -1 and -2 is not rotating normally. [MJ-1107/1108]
  • Code: CC41
  • Description: Paper holder cam home position abnormality: The paper holder cam is not at the home position. [MJ-1107/1108]
  • Code: CC51
  • Description: Punch unit sliding motor (M12)abnormality[MJ-1036]Sideways adjustment motor (M2) abnormality: Sideways adjustment motor is not rotating or puncher is not shifting normally. [MJ-1107/1108 (when MJ-6104 is installed)]
  • Code: CC52
  • Description: Skew adjustment motor (M1) abnormality: Skew adjustment motor is not rotating or puncher is not shifting normally. [MJ-1107/1108 (when MJ-6104 is installed)]
  • Code: CC54
  • Description: Abnormality of paper detection sensors (S24 and S25)[MJ-1036]
  • Code: CC60
  • Description: Punch motor abnormality [MJ-1036]
  • Code: CC61
  • Description: Punch motor abnormality [MJ-1036]Punch motor (M3) home position detection error: Punch motor is not rotating or puncher is not shifting normally. [MJ-1107/1108 (whenMJ-6104 is installed)]
  • Code: CC71
  • Description: Punch ROM checksum error: Abnormality of checksum value on Hole punch controller PC board is detected when the power is turned on. [MJ-1107/1108 (when MJ-6104 is installed)]
  • Code: CC72
  • Description: Punch RAM read/write error: Abnormality of checksum value on Hole punch controller PC board is detected when the power is turned on. [MJ-1107/1108 (when MJ-6104 is installed)]
  • Code: CC80
  • Description: Front alignment motor (M2) abnormality [MJ-1036]Rear alignment motor abnormality: The rear alignment motor is not rotating or the rear alignment plate is not moving normally. [MJ-1107/1108]
  • Code: CC93
  • Description: Knurled roller shift solenoid abnormality [MJ-1036]
  • Code: CC94
  • Description: Fan motor abnormality[MJ-1036]
  • Code: CCF1
  • Description: Tray safety switch abnormality -(1) The tray safety switch turned on during tray operation (moving up or down).(2) The tray operated with the tray safety switch turned on.
  • Code: CDE0
  • Description: Paddle motor abnormality: The paddle motor is not rotating or the paddle is not rotating normally. [MJ-1107/1108]
  • Code: CE00
  • Description: Communication error between finisher and punch unit: Communication error between finisher controller PC board and punch controller PC board[MJ-1107/1108 (when MJ-6104 is installed)]
  • Code: CE10
  • Description: Image quality sensor abnormality (OFF level): The output value of this sensor is out of a specified range when sensor light source is OFF.
  • Code: CE20
  • Description: Image quality sensor abnormality (no pattern level): The output value of this sensor is out of a specified range when the image quality control test pattern is not formed.
  • Code: CE40
  • Description: Image quality control test pattern abnormality: The test pattern is not formed normally.
  • Code: CE41
  • Description: Image quality TRC control test pattern abnormality: The image quality TRC control test pattern is not printed normally.
  • Code: CE50
  • Description: Temperature/humidity sensor abnormality: The output value of this sensor is out of a specified range.
  • Code: CE60
  • Description: Drum thermistor 2 abnormality: The output value of the drum thermistor 2 is out of a specified range.
  • Code: CE70
  • Description: Drum drive switching abnormality: The drum switching detection sensor (S11) is not turned ON after the drum motor was rotated for a specified period of time.
  • Code: CE80
  • Description: LED head communication error
  • Code: CE81
  • Description: Interface initialization error between LED head and LGC board
  • Code: CE90
  • Description: Drum thermistor 1 abnormality: The output value of the drum thermistor 1 is out of a specified range.
  • Code: CF10
  • Description: Communication module writing failure. [MJ-1107/1108]
  • Code: F070
  • Description: Communication error between System-CPUand Engine-CPU
  • Code: F071
  • Description: Communication initialization error betweenSystem-CPU and Engine-CPU
  • Code: F090
  • Description: SRAM abnormality on the SYS board
  • Code: F100_0
  • Description: HDD format error: Operation of HDD key data fails.
  • Code: F100_1
  • Description: HDD format error: Encryption key data of either the SYS board or the SRAM board for the SYS board are damaged.
  • Code: F100_2
  • Description: HDD format error: Encryption key data of both the SYS board and the SRAM board for the SYS board are damaged.
  • Code: F101_0
  • Description: HDD connection error (HDD connection cannot be detected.)
  • Code: F101_1
  • Description: Root partition mount error (HDD formatting fails.): The HDD cannot be connected (mounted) caused by damage to the areas in which the program is mainly stored.
  • Code: F101_2
  • Description: Partition mount error: The HDD cannot be connected (mounted) caused by damage to areas other than those described in the F101_1 and F101_4 to F101_9 errors.
  • Code: F101_3
  • Description: Partition mount error: The HDD cannot be connected (mounted) caused by damage to areas other than those described in the F101_1 and F101_4 to F101_9 errors.
  • Code: F101_4
  • Description: Partition mount error: The HDD cannot be connected (mounted) caused by damage to the "/work" partition.
  • Code: F101_5
  • Description: Partition mount error: The HDD cannot be connected (mounted) caused by damage to the "/registration" partition.
  • Code: F101_6
  • Description: Partition mount error: The HDD cannot be connected (mounted) caused by damage to the "/backup" partition.
  • Code: F101_7
  • Description: Partition mount error: The HDD cannot be connected (mounted) caused by damage to the "/imagedata" partition.
  • Code: F101_8
  • Description: Partition mount error: The HDD cannot be connected (mounted) caused by damage to the "/storage" partition.
  • Code: F101_9
  • Description: Partition mount error: The HDD cannot be connected (mounted) caused by damage to the "/encryption" partition.
  • Code: F102
  • Description: HDD start error: HDD cannot become ‘Ready’state.
  • Code: F103
  • Description: HDD transfer time-out: Reading/writing cannot be performed in the specified period of time.
  • Code: F104
  • Description: HDD data error: Abnormality is detected in the data of HDD.
  • Code: F105
  • Description: HDD other error
  • Code: F106_0
  • Description: ADI-HDD error: Illegal disk replacement detected (ADI-HDD Exchange to SATA-HDD)
  • Code: F106_1
  • Description: ADI-HDD error: HDD type detection error
  • Code: F106_10
  • Description: ADI-HDD error: Error caused by reason other than F106_0 to 5 errors.
  • Code: F106_2
  • Description: ADI-HDD error: ADI encryption key download operation error
  • Code: F106_3
  • Description: ADI-HDD error: ADI authentication AdminPassword generation error
  • Code: F106_4
  • Description: ADI-HDD error: Authentication random number generation error
  • Code: F106_5
  • Description: ADI-HDD error: Authentication data transmission error
  • Code: F106_6
  • Description: ADI-HDD error: Error caused by reason other than F106_0 to 5 errors.
  • Code: F106_7
  • Description: ADI-HDD error: Error caused by reason other than F106_0 to 5 errors.
  • Code: F106_8
  • Description: ADI-HDD error: Error caused by reason other than F106_0 to 5 errors.
  • Code: F106_UND EF
  • Description: ADI-HDD error: Error caused by reason other than F106_0 to 5 errors.
  • Code: F109_0
  • Description: Key consistency error: Consistency check operation error.
  • Code: F109_1
  • Description: Key consistency error: SRAM encryption AESkey data damage.
  • Code: F109_2
  • Description: Key consistency error: Signature Check public key damage.
  • Code: F109_3
  • Description: Key consistency error: HDD encryption parameter damage.
  • Code: F109_4
  • Description: Key consistency error: license data damage.
  • Code: F109_5
  • Description: Key consistency error: Encryption key for ADI- HDD is damaged.
  • Code: F109_6
  • Description: Key consistency error: Administrator password error for ADI-HDD authentication.
  • Code: F110
  • Description: Communication error between System-CPUand Scanner-CPU
  • Code: F111
  • Description: Scanner response abnormality
  • Code: F120
  • Description: Database abnormality: Database is not operating normally.
  • Code: F121
  • Description: Database abnormality (user information management database)
  • Code: F122
  • Description: Database abnormality (Message/Job log management database)
  • Code: F124
  • Description: Database abnormality: Database is not operating normally. (Language management database)
  • Code: F130
  • Description: Invalid MAC address
  • Code: F131
  • Description: Error due to damage to filtering setting file
  • Code: F140
  • Description: ASIC format error: ASIC formatting fails or memory acquiring fails when software is formatted
  • Code: F200
  • Description: Data Overwrite option (GP-1070) disabled
  • Code: F350
  • Description: SYS board abnormality
  • Code: F400
  • Description: SYS cooling fan abnormality
  • Code: F500
  • Description: HD partition damage
  • Code: F510
  • Description: Application start error
  • Code: F520
  • Description: Operating system start error
  • Code: F521
  • Description: Integrity check error
  • Code: F550
  • Description: Encryption partition error
  • Code: F600
  • Description: Software update error
  • Code: F700
  • Description: Overwrite error

 

  • Code: F800
  • Description: Date error
  • Code: F900
  • Description: Machine information alignment error
  • Code: F902_1
  • Description: System firmware / System software model information error - Invalid system firmware/ software is installed.
  • Code: F902_4
  • Description: SYS board model information error

МФУ TOSHIBA
Печать этикеток TOSHIBA
Совместимые картриджи G&G

Поиск по каталогу:

Наименование


Empty cart
Корзина пуста

 МЫ ПРЕДЛАГАЕМ СПЕЦИАЛЬНЫЕ УСЛОВИЯ СОТРУДНИЧЕСТВА ДЛЯ КОРПОРАТИВНЫХ КЛИЕНТОВ И СЕРВИСНЫХ ЦЕНТРОВ